سحب شاحنة Volvo FH500 - FALKOM FAW 25.000 - !! Viewing by appointment only !!

= Additional options and accessories =

- 2 Bedden
- Cabinezijfenders
- Climate Control (ATC)
- Elektrisch spiegels
- Lane Change Support
- Oliekoeler
- SMART TACHO 2
- Standkachel
- Verstralers op het dak
- Volvo Dynamic Steering
- WhatsApp إظهار قائمة الأسماء
- Zwaailampen

= Remarks =

Falkom wrecker installation type FAW 25.000
- One main arm.
- A two-stage hydraulically extendable lift arm, very low; Highest step forearm 195 mm, arm length to center bus frame 4.55 m.
- A fully hydraulic installation consisting of:
- hoses
- couplings
- pipes
- 8-function valve block
- Two double-acting lifting cylinders take care of the up and down movement of the main arm.
- The installation is also executed with a so-called "Powertilt" installation to minimize damage to spoilers e.d.
- The assembly is assembled on a subframe, etc. in accordance with specifications of the truck chassis and sprayed in the primer (RAL 2004).
- 2 anchors model working independently of each other standard.
- A lift beam (100 x 100 mm tube).
- Three sets of fork holders.
- 4 sets of V forks.
- 1 Set of chain forks.
- 1 Set of euro forks (German version 1 set of euro forks model small and 3 set for axle forks).
- Set of Scania claws with mounting brackets on the lift beam.
- Set of air suspension forks.
- 1 bus frame.
- Tow bar mounted.
- Shovel and broom mounted.
- Oil tank.
- Pulling device with trawler in combination with a semi-trailer link.
- Supported drawbar coupling support.
- Two 20 ton hydraulic winches (Sepson H 200), which are equipped with two speeds and a pneumatic freewheel.
- Hydraulic double pump.
- Radio remote control for all functions, excluding anchor shovels
- Complete installation is stacked / metallized.
- Built according to CE guidelines.
- Assembly of the air hands and electrical connections of the truck at the rear in the body.
- Luxury enclosure in aluminum version highly adapted to the 8x4 chassis incl. fly-over, mounting the standard forks in the enclosure, LED cabinet lighting, installation installation on the chassis.
- LED light bar mounted on the flyer.
- Lighting control switches mounted in the control box and in the cabin.
- LED flash lamps mounted at the rear.
- 6 work lights mounted (under the flyer, high at the rear and low).
- LED lamps mounted on the corners of the enclosure.
- Starting aid 12/24 volts.
- Air reel mounted.
- Spray the installation in finish.
- 7-wire electrical cable reel installed.
- Container for counterweight mounted behind the cab.
- Base plate for lateral stability (standard legs only)
- 2 fork raisers
- 2 pieces of anchor plates for Wheel chocks
- Two WLL 15 tonne folding discs
- European approved buffer beam at the rear.
- Pulling device with pin 40, 50 and 60 mm
- 2 models towing eyes.
- RDW inspection and, if necessary, TüV.
- Ballast under the bumper.

= More information =

Cab: Globetrotter, single
Axle 1: Tyre size: 385/65 R22.5; Max. axle load: 9000 kg; Steering; Suspension: leaf suspension
Axle 2: Tyre size: 385/65 R22.5; Max. axle load: 9000 kg; Steering; Suspension: leaf suspension
Axle 3: Tyre size: 315/70 R22.5; Max. axle load: 9500 kg; Reduction: hub reduction; Suspension: air suspension
Axle 4: Tyre size: 315/70 R22.5; Max. axle load: 9500 kg; Reduction: hub reduction; Suspension: air suspension
APK (MOT): tested until 01/2027
Registration number: 28-BPD-3